20% Free Updated Passleader Cisco 642-902 Certification Dumps (221-230)

QUESTION 221
EIGRP has been configured to operate over Frame Relay multipoint connections. What should the bandwidth command be set to?

A.    the CIR rate of the lowest speed connection multiplied by the number of circuits
B.    the CIR rate of the lowest speed connection
C.    the CIR rate of the highest speed connection
D.    the sum of all the CIRs divided by the number of connections

Answer: A

QUESTION 222
Refer to the exhibit. EIGRP is configured on all routes in the network. On a basis of the show ip eigrp topology output provided, what conclusion can be derived?
2221

A.    Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0
B.    Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it declares the neighbor unreachable
C.    Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring for a second successor to network 10.6.1.0/24
D.    Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent about network 10.6.1.0/24

Answer: D

QUESTION 223
Which three route filtering statements are true? (Choose three)

A.    After the router rip and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface.
B.    After the router eigrp 10 and passive-interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
C.    After the router ospf 10 and passive-interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
D.    When you use the passive-interface command with RIPv2, multicasts are sent out the specified interface
E.    When you use the passive-interface command with EIGRP, hello messages are not sent out the specified interface
F.    When you use the passive-interface command with OSPF, hello messages are not sent out the specified interface

Answer: AEF

QUESTION 224
Refer to the exhibit. Routers R1 and R2 are running EIGRP and have converged. On the basis of the information that is presented, which statement is true?
2241

A.    All outgoing routing updates from router R1 to router R2 will be suppressed, but the inbound updates will continue to be received.
B.    All incoming routing updates from R2 will be suppressed, but the outgoing updates will continue to be sent.
C.    Both outgoing and incoming routing updates on R1 will be stopped because of the passive-interface Serial0/0 configuration statement.
D.    Both outgoing and incoming routing updates on R1 will be permitted because the distribute-list 20 out Serial0/0 command cannot be used with association with the outgoing interface.

Answer: C

QUESTION 225
Refer to the exhibit. On the basis of the partial configuration, which two statements are correct? (Choose two.)
2251

A.    Only routes matching 10.0.1.0/24 will be advertised out Ethernet 0.
B.     Only routes 10.0.1.0/24 will be sent out all interfaces.
C.    Only routes 10.0.1.0/24 will be allowed in the routing table.
D.    Only routes matching 10.0.0.0/8 will be advertised out Ethernet 0.
E.    Only routes matching 10.0.0.0/8 will be advertised out interfaces other than Ethernet 0.
F.  All routes will be advertised out interfaces other than Ethernet 0.

Answer: AE

QUESTION 226
Which three statements are true about EIGRP route summarization? (Choose three.)

A.    Manual route summarization is configured in router configuration mode when the router is configured for EIGRP routing.
B.    Manual route summarization is configured on the interface.
C.    When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes.
D.    The ip summary-address eigrp command generates a default route with an administrative distance of 90.
E.    The ip summary-address eigrp command generates a default route with an administrative distance of 5.
F.    When manual summarization is configured, the router immediately creates a route that points to null0 interface.

Answer: BEF

QUESTION 227
Refer to the exhibit. Network 10.0.0.0/8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0/8 network is true?
2271

A.    Router R1 will be preferred because its neighbor has the higher autonomous system number.
B.     Router R1 will be preferred because it has the lower neighbor IP address.
C.     Router R1 will be preferred because it has a lower local preference.
D.    Router R2 will be preferred because its neighbor has a lower autonomous system number.
E.    Router R2 will be preferred because it has the higher neighbor IP address.
F.     Router R2 will be preferred because it has a higher local preference.

Answer: F

QUESTION 228
What does the default value of the EIGRP variance command of 1 mean?

A.    Load balancing is disabled on this router.
B.    The router performs equal-cost load balancing.
C.    Only the path that is the feasible successor should be used.
D.    The router only performs equal-cost load balancing on all paths that have a metric greater than 1.

Answer: B

QUESTION 229
What technique should be used on BGP edge routers to prevent a multi-homed autonomous system from becoming a transit system?

A.    Advertise with a high MED value all networks that are discovered via external BGP.
B.     Remove the AS-Path information on all routes in the BGP table prior to advertising externally.
C.     Only advertise networks externally if they have been discovered via internal BGP.
D.    Use an outgoing distribution list to filter all networks not originating from inside the autonomous system.
E.    Set the no-export community attribute on all networks that are advertised externally.
F.     Set the origin code to incomplete for all networks that are discovered via external BGP.

Answer: D

QUESTION 230
Refer to the exhibit. In the show ipv6 route output, what would the metric be for a summary route that summarizes all three OSPFv3 routes displayed?
2301

A.    20
B.    40
C.    100
D.    120
E.    140
F.    160

Answer: C

20% Free Updated Passleader Cisco 642-902 Certification Dumps