QUESTION 191
If a metric is not specified for routes that are redistributed into OSPF, the default metric that is assigned to the routes is 20, except for redistributed BGP routes. What is the metric that is assigned to redistributed BGP routes? Select the best response.
A. 0
B. 1
C. 10
D. 200
Answer: B
QUESTION 192
According to RFC 2328, what is the stateful order in which an OSPF router transitions to a full adjacency with a neighbor router?
A. Down, Init, 2-Way, Exstart, Exchange, Loading, and Full
B. Down, Init, 2-Way, Exchange, Exstart, Loading, and Full
C. Down, 2-Way, Init, Loading, Exstart, Exchange, and Full
D. Down, 2-Way, Init, Exchange, Exstart, Loading, and Full
E. Down, Init, 2-Way, Loading, Exstart, Exchange, and Full
F. Down, 2-Way, Init, Exstart, Exchange, Loading, and Full
Answer: A
QUESTION 193
During a redistribution of routes from OSPF into EIGRP, an administrator notices that none of the OSPF routes are showing in EIGRP. What are two possible causes? (Choose two.)
A. incorrect distribute lists have been configured
B. missing ip classless command
C. CEF not enabled
D. no default metric configured for EIGRP
Answer: AD
QUESTION 194
To enable BGP tunneling over an IPv4 backbone, the IPv4 address 192.168.30.1 is converted into a valid IPv6 address. Which three IPv6 addresses are acceptable formats for the IPv4 address? (Choose three.)
A. 192.168.30.1:0:0:0:0:0:0
B. 0:0:0:0:0:0:192.168.30.1
C. ::192.168.30.1
D. C0A8:1E01::
E. 192.168.30.1::
F. ::C0A8:1E01
Answer: BCF
QUESTION 195
What is IPv6 router solicitation?
A. a request made by a node to join a specified multicast group
B. a request made by a node for its IP address
C. a request made by a node for the IP address of the DHCP server
D. a request made by a node for the IP address of the local router
Answer: D
QUESTION 196
Your Lead2pass trainee asks you, in the context of IPv6 and OSPF, what best describes a type 9 LSA? What should you tell her?
A. Link LSA
B. Interarea prefix LSA for ABRs
C. Router LSA
D. Switch LSA
E. Intra-area prefix LSA
F. None of the above
Answer: E
QUESTION 197
You have been tasked with setting up OSPF on an existing Lead2pass router using IPv6. Which command enables OSPF for IPv6 on a router?
A. ipv6 router ospf process-id
B. router ospf process-id
C. router ospf ipv6 process-id
D. ipv6 ospf process-id area-id
E. None of the above
Answer: A
QUESTION 198
Lead2pass plans on migrating their network from IPv4 to IPv6 in the near future. Which three techniques can be used to transition from IPv4 to IPv6? (Select three)
A. Dual stack
B. NAT
C. Flow label
D. Mobile IP
E. 6to4 tunneling
F. Anycast
G. MBGP
Answer: ABE
QUESTION 199
Which command must be globally enabled on a Cisco router to support IPv6?
A. ip routing ipv6
B. ipv6 unicast-routing
C. ipv6 routing
D. ip classless
E. ipv6 cef
Answer: B
QUESTION 200
What number is a valid representation for the 200F:0000:AB00:0000:0000:0000:0000/56 IPv6 prefix?
A. 200F:0:0:AB/56
B. 200F:0:AB00::/56
C. 200F::AB00/56
D. 200F:AB/56
Answer: B
20% Free Updated Passleader Cisco 642-902 Certification Dumps
