QUESTION 181
Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1? Select the best response.
A. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs.
B. Only redistributed RIP routes will appear in Area 1. They will be advertised via type 7 LSAs.
C. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs.
D. No redistributed routes can appear in Area 1, only summary routes.
Answer: C
QUESTION 182
Which statement is true about IPv6? Select the best response.
A. Only one IPv6 address is assigned per node.
B. Only one IPv6 address can be assigned to each interface.
C. Each host can autoconfigure its address without the aid of a DHCP server.
D. IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
Answer: C
QUESTION 183
What is the IPv6 address FF02::2 used for? Select the best response.
A. all hosts in a local segment
B. all routers in a local segment
C. all hosts in a particular multicast group
D. all routers in an autonomous system
Answer: B
QUESTION 184
What does the command clear ipv6 ospf process accomplish? Select the best response.
A. The OSPF adjacencies are cleared and initiated again.
B. The route table is cleared. Then the OSPF neighbors are reformed.
C. The shortest path first (SPF) algorithm is performed on the LSA database.
D. The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
Answer: D
QUESTION 185
In IPv6, the interfaces running OSPF can be configured with multiple address prefixes. Which statement is true about the IPv6 addresses that can be included into the OSPF process? Select the best response.
A. Specific addresses cannot be selected for importation into the OSPF process.
B. Specific addresses can be selected using an ACL.
C. Specific addresses can be selected using a route map.
D. Specific addresses can be selected using a prefix list.
Answer: A
QUESTION 186
Which statement is true about the command ipv6 ospf 1 area 0? Select the best response.
A. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
B. It must be issued in interface configuration mode to enable the OSPF process for IPv6.
C. It must be issued before the network command to enable the OSPF process for IPv6.
D. It must be issued after the network command to enable the OSPF process for IPv6.
Answer: B
QUESTION 187
Refer to the exhibit. EIGRP has been configured on all routers in the network. The command metric weights 0 0 1 0 0 has been added to the EIGRP process so that only the delay metric is used in the path calculations. Which router will R1 select as the successor and feasible successor for Network A? Select the best response.
A. R4 becomes the successor for Network A and will be placed in the routing table. R2 becomes the feasible successor for Network A.
B. R4 becomes the successor for Network A and will be included in the routing table. No feasible successor will be selected as the advertised distance from R2 is higher than the feasible distance.
C. R2 becomes the successor and will be placed in the routing table. R4 becomes the feasible successor for Network A.
D. R2 becomes the successor and will be placed in the routing table. No feasible successor will be selected as the reported distance from R4 is lower than the feasible distance.
Answer: B
QUESTION 188
Refer to the exhibit. Which interoperability technique implemented on the dual-stack routers would allow connectivity between IPv6 sites across automatic created tunnels using the 2002::/16 prefix? Select the best response.
A. Dual Stack
B. NAT-PT
C. 6to4 tunnel
D. GRE tunnel
E. ISATAP tunnel
Answer: C
QUESTION 189
Refer to the exhibit. Based on the output from the show command on RT1which statement is true? Select the best response.
A. OSPFv3 uses global IPv6 addresses to establish neighbor adjacencies.
B. RT1 has a subnet mask of 64 bits.
C. RT1 has FastEthernet0/0 set as a DR for network type broadcast.
D. OSPFv3 uses Link-local addresses to establish neighbor adjacencies.
E. RT1 does not have a global IPv6 address set on FastEthernet0/0.
F. OSPFv3 uses IPv4 addresses to establish neighbor adjacencies.
Answer: D
QUESTION 190
Refer to the exhibit. Which statement is true about the 6.6.6.0/24 prefix? Select the best response.
A. If another path advertises the 6.6.6.0/24 path and has the default local preference, that path is more preferred.
B. The command neighbor send-community is configured on BGP neighbor 10.10.23.3.
C. The route 10.10.23.3 is not being advertised to other BGP neighbors.
D. Route 6.6.6.0/24 is learned by an IBGP peer.
Answer: B
20% Free Updated Passleader Cisco 642-902 Certification Dumps
